In this issue, we discuss some of the challenges, pitfalls and mitigations to consider when designing non-standard board geometries. We share strategies for designing odd-shaped PCBs, including manufacturing trade-offs and considerations required for different segments and perspectives.
On the subject of simplification, our expert contributors explain how to design PCBs without making them complex and over-constrained—whatever the level of technology. In addition, we discuss the effect your decisions and tradeoffs have on design complexity. 94vo Circuit Board
Our expert contributors discuss how PCB designers can utilize standards to save time and money, not to mention frustration. We also spotlight the newly updated version of the IPC Checklist, a handy guide that illustrates which standards cover which topics, from front-end design through assembly.
Introduction One of the biggest challenges facing PCB designers is understanding the cost drivers in the PCB manufacturing process. This article is the first in a series that will discuss these cost drivers (from the PCB manufacturer’s perspective) and the design decisions that will impact product reliability.
DFM Design for manufacturing (DFM) is defined as the practice of designing printed circuit boards that meet not only the capabilities of the customer’s assembly manufacturing process, but also the capabilities of the board fabrication process at the lowest possible cost. While not a substitute for early design engagement with the PCB fabricator, these articles will provide guidelines that will help you to “design for success.”
Standard Multilayer Materials Most PCBs are manufactured using epoxy-glass (FR-4) dielectrics and copper foil. PCBs are constructed from three basic material types: copper foil, prepreg, and cores.
Figure 1: An example of fully-cured glass-epoxy material with copper laminated to both sides.
High Frequency (RF/Microwave) Materials High-frequency designs (1 GHz and up) require materials with closely controlled dielectric constants and dissipation factors. The FR-4 materials normally used for PCBs don’t have the desired controlled characteristics. The substrate materials used for high frequency applications were originally based upon PTFE resin formulations that have the desired properties, i.e., dielectric constant controlled to ±0.04 and dissipation factor to 0.0004. These values may vary somewhat depending on the material type and supplier. Today, there are a number of materials on the market that do not contain PTFE, but still have controlled values that can be used for high frequency applications.
Material Types There are three basic material types: non-woven glass, woven glass, and filled. Military specification designations are GR (non-woven) and GT, GX, and GY (woven). Filled material has no designation.
Non-woven materials contain a dispersion of glass microfibers in the substrate. These are typically materials with low dielectric constants (2.20-2.35). They work very well at the higher frequencies, as the dissipation factor is low.
Copper Foil Types Two types of bonded copper foil are available; electrodeposited (ED) and rolled-annealed (RA). The difference between these foils is the fabrication process and the treatment on the backside to enhance bonding adhesion.
1. Electrodeposited copper (ED) is made by electroplating copper onto a rotating drum that results in a vertically-oriented grain structure (Figure 2). Opposite the drum surface, the copper plating is rough, almost like “teeth,” and enhanced by further treatment. The teeth provide higher peel strength but may increase conductor losses at high frequency because of the depth of the teeth.
Figure 2: Electrodeposited copper made by electroplating onto a rotating drum.
2. Rolled-annealed copper (RA) is made by rolling an ingot to very thin foils. The grain structure is horizontally oriented. The rolling causes stress in the foil and must be heat annealed to remove the stress. Rolled-annealed copper has the same finish on each side, which requires teeth artificially created on the backside. These teeth are about half the depth of the electrodeposited copper. This causes rolled-annealed copper to have about half the peel strength of electrodeposited copper. This means rolled-annealed copper performs better at frequencies above 13 GHz.
Figure 3: Rolled-annealed (RA) copper is made by rolling an ingot into very thin foils.
Peel strength is the amount of force, in pounds per inch, which must be applied to cause a 1-inch-wide strip of the copper foil to peel from the substrate. Typical values for electrodeposited (ED) 1-ounce copper are 9–11 pounds per inch and rolled-annealed (RA) 1 ounce copper is 4–6 pounds per inch. As circuit traces become narrower the peel strength is reduced. Therefore, more care is required to solder and bond to narrow traces.
Copper surface roughness is critical for high-frequency applications where the roughness of the copper surface impacts conductor loss. At high signal frequencies, the current in a PCB copper circuit is concentrated within a small depth near its surface, referred to as the skin effect, or skin depth. Skin depth is a measure of how (and where) electrical conduction takes place in a conductor and is a function of frequency.
In other words, for high frequency applications, the smoother the surface copper the better. Circuit conduction occurs at the surface nearest the dielectric from which the EM wave propagates, in other words, the bottom copper surface that is against the laminate in a microstrip design.
Figure 4: The smoother the surface of copper, the better.
Metal Core and IMPCB Materials Insulated metal printed circuit boards (IMPCB) or metal core PCBs are thermal management designs that utilize a layer of solid metal to dissipate the heat generated by the various components on the PCBs. When metal is attached to a PCB, the bonding material can either be thermally conductive but electrically isolative, or in the case of RF/microwave circuits, the bonding material may be both electrically and thermally conductive. There are two common metals used in these applications: copper and aluminum. Which to use depends on the application with consideration for cost, weight, and thermal properties. Table 1 presents the properties of the various base metals.
Table 1: A list of various properties of a few metal base materials.
Embedded Capacitance Materials Embedded capacitance material consists of a very thin layer of ceramic-filled epoxy sandwiched between two layers of copper foil. It can be patterned as a power and ground plane pair for a lower impedance, shared capacitance power distribution network. The biggest design benefit is that it increases the usable board area by allowing for the removal of many, if not all, capacitors equal to or below 0.1 ?F and their associated solder joints and vias. Additional benefits include:
Embedded Resistor Materials Embedded resistors are planar resistive elements made into a thin film. This type of resistor becomes part of the etched and printed circuitry on the standard printed circuit board layer as it eliminates the need for solder joints.
Conclusion As you can see, there are many manufacturing factors that contribute to the final cost of every PCB. Today’s PCB designer must have a thorough understanding of these cost drivers, as well as the many trade-offs involved in managing these factors in each design. Stay tuned for Part 2 of this series.
Pcb Terminals Anaya Vardya is president and CEO of American Standard Circuits; co-author of The Printed Circuit Designer’s Guide to… Fundamentals of RF/Microwave PCBs and Flex and Rigid-Flex Fundamentals; and author of Thermal Management: A Fabricator's Perspective. Visit I-007eBooks.com to download these and other free, educational titles. He also co-authored “Fundamentals of Printed Circuit Board Technologies.”